How To Make Your Own Plastic Molded Objects
Posted: Monday, August 01, 2005
by Paul S Umstead
Char's eBay Gift Emporium
Making your own gifts can be satisfying and memorable to the recipient. It would be extremely helpful for you to read this article, print it off and familiarize yourself with the products and terminology.
SULPHO-PLASTICS
This plastic is particularly adaptable for making molds and light castings requiring tensile strength but very clear outline. It may also be used for making ornaments and novelties. However, as this is flammable, do not use for ashtrays.
Interesting marble effects may be obtained by varying the filler used and by substituting a small quantity of chalk to replace some of the graphite, a very pleasing glazed surface marble is formed.
As long as the graphite is retained as a filler, this plastic may be electroplated and forms a very economical base for such work.
FORMULA: Mix thoroughly and smoothly together 25 parts of GRAPHITE and 75 parts SULPHUR and place over heat. As soon as the mass has melted and runs like water, remove from the heat. In any case, a temperature of 235 degrees F. not be exceeded. If heated about 250 degrees F. the plastic will form a rubbery mass and will have to be cooled and reheated. In this liquid state the plastic is ready for casting and may be poured into smooth surfaced molds.
N.B. to heat this mixture properly, a good even heat is necessary. Should the heating be done by flame, the container should be placed in a sand bath to insure an even heating surface. The cast-iron top of a heater or stove is excellent.
EQUIPMENT: The only equipment for the above that is required is space enough to work in, a stove or heater, a pan to heat the mixture in and a bench or table.
PROCEDURE: Before making any casting you will need a pattern. After choosing a design that fits your need, your next step is to make the mold. Then you may start into production. If your product requires any holes, threads or machining, this may be done in the same manner as in working with a metal casting.
Always think of your castings as metal, for they have metallic properties, i.e., conduct heat, electricity and can be electroplated. In fact, the most valuable quality of Sulpho-Plastic is the fact that it can be used as a metal substitute. This permits you to make products that look and are as good and even better, in some cases, than a true metal. For instance, to make a chrome plated metal lamp base or other metal casting would require foundry equipment and machine shop work and in all, a process miles out of the reach of the small manufacturer. However, with our plastic, a lamp base, similar in all respects, may be made for a fraction of the other cost.
ELECTROPLATING: While this can be done at home with very little equipment, it is advisable to have it done by a commercial electroplater, who does it very cheaply and much more efficiently. Electroplating is only used on expensive replicas and is not advisable for a start.
DESIGN: The number and variety of articles that can be manufactured from Sulpho-Plastic is practically unlimited and to make a complete list would be impossible. However, any article of reasonable size and simplicity of design such as lamps, curios, buddhas, incense burners, elephants, vases, plaques, brooches, desk-sets, toys paper weights, etc., may be cast by using an original or purchased article for a pattern or model - or an original design may be patterned in clay and used to make a mold. It is advisable for the beginner to choose a simple article for a start, preferably solid, such as paper weights or book-ends.
MOLDS: Molds may be made of metal or plaster of paris. Metal molds, however, require a great deal of skill and equipment to produce. Therefore for the beginner, it is advisable to use plaster of paris.
To make plaster of paris molds first obtain a box, wood or cardboard will do about an inch longer each way than the article to be cast. Coat the inside of the box very thoroughly, yet thinly, with stearine or sweet oil. Use this also on the article to be cast. This acts as a lubricant and the plaster of paris will not cement itself to either the box or the article, if the oil is evenly distributed.
Now, next make a thick, creamy mixture of plaster of paris by sifting the plaster gradually into the water, stirring constantly to prevent lumping. Let this stand a few minutes to allow the air bubbles to escape. Pour mixture slowly over pattern in this box to about double the thickness of the pattern.
Allow several hours to dry, then remove. If the stearine or sweet oil was applied properly, this will be easy. When the mold is thoroughly dry, give it a coat (thin) of shellac and repeat in 12 hours. Mold is now ready for use.
MOLDING: First and foremost always make sure that you have lubricated your mold with beeswax or stearine. Place molds on a reasonably level surface and pour the sulpho-plastic into the mold, quickly and smoothly. Do not pour from a height as this will break the lubricant and leaves blemishes on the casting.
Plastic must be poured quickly to prevent cooling in folds and thus making a poor casting. One of the big assets of sulpho-plastics is the fact that it dries and hardens almost immediately. There is no long wait for casting to dry. It is best to test this process with some objects that you don't intend to give as gifts, as you will find that practice will hone your skills and your results. Good luck and most of all, have fun!
This Article has been viewed 20,634 times. (Not updated in real-time.)
Top-level comments on this article: (9 total)I want to make a spoiler for an automobile; is it possible to do so using this method?
Very interesting; where would one get graphite and sulphur though?
This is what I've been looking for (theoretically anyhow...lol). I do have a question though...........There are many different types of sulfur out there... what kind do I need to use in order for this to work effectively in order to put out a professional product? Thank you for your time and assistance. Respectfully, Evergreen Rogue
i have used it for my PO
Would you be kind enough to tell me where I can buy sulpho plastic ? I can't wait to try it.....
Where can I get Graphite?Graphite is pencil lead.
Where could i get sulphur to make RC plastic car bodies?
Sulphur is sold at most hardware stores in the gardening section. It is probably pure enough at 95%. I wonder if charcoal could also be used, since it is nearly pure carbon, though the molecular structure is a bit different than graphite.
Also thought I should mention that sulphur auto-ignites very easily, burning with a nearly invisible blue flame and releasing terrible fumes.
We want your comments! If you can read this, you don't have javascript enabled, so you can't use this comment system. Please enable javascript.